發現很多車主對于變速箱換油保養也是非常不重視，像那種由于缺油導致變速箱內部零件被磨的稀碎的也是非常常見的現象。所以今天就來講講
濟南變速箱油位的檢查方式，如下：
It is found that many car owners also pay little attention to the oil change and maintenance of the transmission. It is also a very common phenomenon that the internal parts of the transmission are worn and broken due to lack of oil. So today we will talk about the inspection method of Jinan transmission oil level, as follows:
變速箱油位檢查分兩種方法：
There are two methods to check the transmission oil level:
一種是變速箱附帶油尺：將車停在水平地面上，拉緊手剎，空擋狀態下怠速運轉發動機使油溫達到60度左右。再進行切換手柄操作，使擋位桿在各擋位停留3秒鐘，以便液力變矩器和所有換擋執行器充滿液壓油，后掛入P擋狀態。
One is the oil dipstick attached to the transmission: park the vehicle on the level ground, tighten the hand brake, and idle the engine in neutral to make the oil temperature reach about 60 degrees. Then operate the switch handle to keep the shift lever in each gear for 3 seconds, so that the hydraulic torque converter and all shift actuators are filled with hydraulic oil, and then shift into P gear.
開始檢查油尺，先從油管內把油尺拔出來把表面油漬擦干凈，再將擦干凈的油尺全部插入加油管后再拔出來。觀察油面高度，正常油量應該是在上線與下線之間，油尺的2/3刻度處。如果低于低刻度線，說明油少了，如果高于高刻度線，說明油多了。（這里要特別提醒大家，在啟動發動機之前一定要確保油尺油浸深度不能小于10mm，然后才能開始進行波箱預熱操作。）一種是未帶油尺：變速箱沒有油尺的話可以通過溢流孔進行檢測。溢流孔有的是在變速箱下面，有的是在油底殼上方，有的是在變速箱中殼上面。
Start to check the dipstick. First pull the dipstick out of the oil pipe to clean the oil stains on the surface, and then insert the cleaned dipstick into the oil filling pipe before pulling it out. Observe the oil level height. The normal oil level should be between the upper and lower line, at the 2/3 scale of the dipstick. If it is lower than the low scale mark, it means less oil. If it is higher than the high scale mark, it means more oil. (Here, we should particularly remind you that before starting the engine, you must ensure that the oil immersion depth of the oil dipstick cannot be less than 10mm, and then start the wave box preheating operation.) One is without the oil dipstick: if there is no oil dipstick in the transmission, it can be detected through the overflow hole. The overflow holes are under the transmission, above the oil pan, and above the middle housing of the transmission.
著車狀態（注意也有小部分車需要熄火檢測）下，擰開油位螺絲，流淌出的油液呈現出“連續的線狀”即為正常油位。
When the vehicle is running (note that a small number of vehicles need to be flamed out), unscrew the oil level screw, and the flowing oil shows "continuous linear", which is the normal oil level.
換油的話油品的選擇，小編也建議大家好使用原廠油比較穩妥，如果大家有足夠的財力想選品質更好的也是可以的，但是切記一定不能比原廠油差，更不能加錯油！像干式雙離合、濕式雙離合變速箱油都是專用的，對變速箱油的要求也是比較高，千萬不能圖便宜！
When changing the oil, the editor also suggested that it is safer to use the original oil. If you have enough money to choose the better quality oil, you can also do it, but remember that it must not be worse than the original oil, let alone add the wrong oil! For example, the dry double clutch and wet double clutch transmission oil are all special, and the requirements for transmission oil are also relatively high. Don't try to be cheap!
The above is a little knowledge about oil change and maintenance for cars that I compiled for you. I hope it can help you. In addition, if you have any problems with the transmission of the car, you can consult us http://m.haoyouyuan.com.cn oh
